10 Whirlpool Dishwasher Error Codes and How to Fix them

March 30, 2022

Whirlpool Top Control Dishwasher Repair Service | Whirlpool Appliance Repair
Home » Blog » 10 Whirlpool Dishwasher Error Codes and How to Fix them

When a dishwasher breaks down, Whirlpool Appliance Repair can restore your kitchen’s efficiency and time savings. Directly contacting the top Whirlpool Appliance Repair in New York specialists will provide you with the greatest Whirlpool dishwasher repair, as they are the most qualified to support your appliance service and repair needs. In addition, as experts in their industries, they provide unequaled technical expertise, technician availability, and parts access to provide you with the quickest solution to any service or repair inquiry.

If your Whirlpool dishwasher isn’t working properly, it’s fair to assume it’s developed a problem. It may seem intimidating to investigate the problem yourself, but if your dishwasher displays an error number or the start button light flashes, your helpful machine is alerting you to the source of the problem.

A two-digit number beginning with F or a flashing start button light that pauses occasionally are common Whirlpool dishwasher problem codes. You’ll need to count the number of flashes between each pause to figure out which code your Whirlpool dishwasher is showing. Most Whirlpool dishwasher models, as well as several other dishwasher brands, are covered by these Whirlpool dishwasher codes.

Continue reading to learn which portion of your dishwasher is causing the fault code to appear, as well as how to resolve your Whirlpool dishwasher issues.

F1 (or 1 flash) – Temperature sensor

Your machine’s temperature sensor has identified that the water temperature is either too low (below -3°C) or too high (over 85°C). It’s possible that the water entering your machine is at an odd temperature, but the NTC temperature sensor is most likely broken and has to be replaced.

F2 (or 2 flashes) – Water leak

If you notice this error, your system most likely has a leak. To solve the problem, you’ll need to empty the base, locate the leak, and repair it.

F3 (or 3 flashes) – Heating System

It’s possible that the following factors are causing your dishwasher to not heat or heat too slowly:

– A defective heating element — this is the most likely source of the problem.

– A temperature sensor that isn’t working properly.

– A bad connection between the heater and the control board (check the relay connections on the PCB)

F4 (or 4 flashes) – Drainage system

This issue means that your system hasn’t been able to drain properly. This problem might be caused by a clogged or malfunctioning drain pump or line. If this is the case, the pump will need to be cleaned or replaced. The issue might potentially be caused by the machine siphoning if the hose pressure is too low, an optical sensor, or even the control board on rare occasions.

F5 (or 5 flashes) – Rotor blocked

An issue has arisen with the wash motor’s rotor (the part which moves). If this happens, your dishwasher motor may need to be replaced.

F6 (or 6 flashes) – Not filling

The inlet valve that allows water into your machine may need to be replaced, or the inlet hose may be blocked. There might also be an issue with the water supply to your machine – if the tap leading to the hose is turned off or low.

F7 (or 7 flashes) – Flow Meter

F7 is particular to the flow meter however it might also be caused by faults similar to F6, such as:

– A kink or obstruction in the water input hose

– A malfunctioning water intake valve

– A shut-off water faucet

F8 (or 8 flashes) – Water Level

This error number will show if there is too much water detected in your dishwasher. The problem with the water level might be caused by:

– A clogged filter that prevents your machine from emptying

– An issue with the mechanism that allows water to enter your machine

– An excessive amount of foaming in the machine (possibly caused by adding too much detergent)

– A malfunction with the primary wash motor caused a spray pump failure.

F9 (or 9 flashes) – Continuous water inlet

A dishwasher fills up with water indefinitely for one of two reasons. Either the inlet valve is malfunctioning and not closing, or the main control board has a short circuit. It’s possible that the valve or control board has to be changed.

F0 (or 10 flashes) – Sensor failure

Your machine may have sensors for water temperature, input flow, or even water level/flow pressure.

You can immediately wash away the filth from your plates with our service. When your dishwasher functions properly, you may enjoy convenience in the kitchen once more. Schedule an appointment with us right now, and we’ll take care of your technological concerns as seamlessly as your dishwasher.

Whirlpool Appliance Repair | Whirlpool Appliance Repair


Whirlpool Appliance Repair can and will repair any fault diagnostics with your Whirlpool appliances. Contact Whirlpool Appliance Repair today!